Skip to main content
Version: 14.0

Theatre Programming Quick Guide

If you are used to programming other theatre-style consoles, you will be more familiar with using a keypad/syntax style interface, rather than the Titan touchscreen. But fear not because you can program a theatre show on Titan using keypad syntax and this is how you do it.

  • Labelled buttons on the console are shown like this: Enter.
  • The @ button< is the one next to the numeric keypad.
  • The Cue button is labelled Connect or Connect/Cue on some consoles.
  • The Thru button is labelled Thru or Through on some consoles.
  • The And and Thru buttons are not provided as fixed buttons on some consoles, softkey And and Through options are provided instead.

Dimmers/Fixtures have a User Number (which is equivalent to the Channel Number on other consoles), shown in the top left corner of the fixture button. This is the number n shown in the keypad commands below. You can change this number using the Set Legend softkey, see section Changing the Patch. Groups also have a User Number.

Fixtures Window showing user numbers

Setting Dimmer/Fixture Levels

n @ @Set fixture n to 100%
n @ v EnterSet fixture n to v% (you need to enter 2 digits so "50" for 50%)
n Thru m @ v EnterSet fixtures n - m to v%
n And m And p @ v EnterSet fixtures n, m, p to v%
Group n @ v EnterSet fixtures in group n to v%
ClearSnap release edited channels back to programmed state - like Cheat on ETC
t ClearRelease edited channels fading over time t

Setting Other Attributes of Intelligent Fixtures

n EnterSelect fixture n for control
n Thru m EnterSelect fixtures n to m for control
Group n EnterSelect all fixtures in group n for control

Once you have selected the fixtures:

  • Press one of the Attribute Bank buttons Colour Gobo etc. The current function of the wheels is shown bottom right on the screen. Press the same Attribute Bank again to page through different attributes e.g. if there are 2 gobo wheels keep pressing Gobo to access the other attributes.

  • Use the wheels to set the value. Or press the @ button next to the wheel and type in a value on the keypad.

Programming Cues

Titan can have multiple cue lists. To start a cue list press Record then select Create Cue List from the touch screen. Then press a Select button above the fader where you want to store the cue list.

Titan will record into the cue only the dimmers/fixtures you have changed since you last pressed Clear, and that have changed from the previous cue (so if you put up another playback, that won't get recorded). To record everything with intensity above zero, switch  Record Mode to "Record by Stage" (see Creating a Cue).

Record {fader select} {fader select}Record the next cue onto the end of the cue list on this fader
Record Cue n EnterRecord cue n (will prompt for merge/overwrite if it exists already)
Time t EnterSet fade time into programmer (does not affect stored cues; will save with the cue when you record it)
Cue n Time t EnterSet fade time of cue n to t seconds
Delete Cue n Enter EnterDelete cue n (2^nd^ Enter confirms)
Copy Cue n @ Cue m EnterCopy cue n to new cue m
Copy Cue n @ EnterCopy cue n onto the end of the cue list
View/Open {fader select}Show the list of cues on screen, click on individual times to edit them
  • For the copy commands, you can use Move in place of Copyto move cues. For consoles which don't have a Move button you can press (Avo and Copy) together to get Move.

  • You can select multiple cues using Thru, And and Not. For example to copy cues 3, 4 ,5 ,7, 10 into a new block of cues starting at cue 20 you could do

Copy {fader select} 3 Thru 7 Not 6 And 10 @ 20 Enter
  • To make a Block cue (changes from previous cues do not track), view the cue list as above, in the Tracking column click the cell for the cue you want to change and select Block from the softkeys.

  • To link cues so they automatically run after each other, the easiest way is on the screen. Click on the "Link" cell (which normally shows "Wait For Go". Then select from the softkeys

    Link After Previous Cue or Link With Previous Cue. For Link After, set the "Delay Out" time to set how long the cue will remain before the next cue starts.

Running Cues

Push up the fader of the cue list to make it active. Titan calls this the connected cue list and the control buttons such as Go will operate on this cue list.

Cue {fader select}If another cue list is active, connect this cue list as the current list
GoRun next cue with programmed times
Cue n GoGo cue n with programmed times
 t GoNext cue go with fade time t
 n Cue t GoJump to cue n with fade time t
  • If you want moving fixtures to automatically position themselves ready for the next cue, enable the Move In Dark option, see Move In Dark. This option is Off by default.

Editing Cues While Running

Often you need to make changes to cues while the cue is active in a running show. Press Clear before you make changes to be sure that the programmer does not contain any previous changes.

Record Cue CueUpdate current cue by merging programmer
Time t Enter Record Cue CueSet fade in time of current cue (It is probably easier to use View and click on the time on screen to edit it)


You can't select Effects/Shapes from the keypad on Titan, but it's still easy:

  1. Select fixtures for control

  2. At the top level menu press Shapes and Effects, Shape Generator, Create

  3. Select the type of shape Dimmer, Pan/Tilt etc

  4. Select a shape from the softkeys or from the Shapes window which appears

  5. Set the Speed, Size, Spread using the wheels

Shapes will record into cues, and will track through subsequent cues. You can deactivate tracked shapes in the Playback View, or set the Shape Tracking in the Playback Options.